Wuxi, China · Manufacturer & exporter since 2016info@jcpipeline.com+86 18130056225
Home Products
Product ranges
Hot Tapping Machines Projects News About Contact
Home/Products/Hot Tapping Machines/Electric Hot Tapping Machines/Electric Hot Tapping Machine JC-E800-1600
Electric Hot Tapping Machine JC-E800-1600
09 · JC-E800-1600

Electric Hot Tapping Machine JC-E800-1600

Electric Hot Tapping Machine JC-E800-1600 cuts branches from DN700 – DN1600 (32" – 64") into live mains up to 16 bar. An 11 kW motor at 380 V / 50 Hz runs the bar at 10 r/min, and the manual feed advances the cutter at 0.1 – 0.15 mm/r; one hole takes 100 – 240 min. Travel is 1600 mm, so a standard gate valve and tapping adapter fit above the pipe. The machine mounts on a flange connection and weighs 2200 kg.

Key features

  • Working pressure ≤ 16 bar (PN16)
  • Tapping range DN700 – DN1600
  • 1600 mm boring bar travel
  • 11 kW motor, 380 V, 50 Hz, 10 r/min
  • Feed 0.1 – 0.15 mm/r, 100 – 240 min per hole
  • Flange connection, BS or ASME
  • Rated for water, oil, gas and steam

Lead time 25–35 working days after deposit. Test record, drawing and packing list go with every shipment. Payment: 30% T/T deposit, balance against copy of B/L.

Specifications

Tapping range32" – 64" (DN700 – DN1600)
Tapping sizes32", 36", 40", 48", 56", 64" (DN800, DN900, DN1000, DN1200, DN1400, DN1600)
Working pressure≤ 16 bar (PN16 / 232 psi)
Working temperatureup to +200 °C
Boring bar travel1600 mm
Spindle speed10 r/min
Feed modeManual
Feed volume0.1 – 0.15 mm/r
Tapping time100 – 240 min per hole
Drive modeElectric motor
Motor power11 kW
Motor voltage380 V
Frequency50 Hz
Connection to valveFlange
Flange standardBS or ASME
Pipe mediumWater, oil, gas and steam
Pipe materialSteel, cast iron, plastic and concrete pipe
Dimensions3000 × 1200 × 1500 mm
Weight2200 kg

Typical applications

Raw water and sewer force mainsLarge-diameter trunk mainsCirculating-water and outfall linesTransmission and trunk mainsPower plant cooling-water headers
Product details

Overview

Electric Hot Tapping Machine JC-E800-1600 cuts branches from DN700 – DN1600 (32" – 64") into live mains up to 16 bar. An 11 kW motor at 380 V / 50 Hz runs the bar at 10 r/min, and the manual feed advances the cutter at 0.1 – 0.15 mm/r; one hole takes 100 – 240 min. Travel is 1600 mm, so a standard gate valve and tapping adapter fit above the pipe. The machine mounts on a flange connection and weighs 2200 kg.

Transmission-main size. The machine is crane-set on the tapping flange; 1,600 mm of travel and an 11 kW drive cut a 64 inch branch in one continuous pass.

Models are listed with the flange pattern they are built to: BS or ASME.

Tapping sequence

  1. Fit the tapping saddle or flange to the pipe and pressure-test the branch.
  2. Bolt the valve and the machine to the connection; check the bar is square to the pipe.
  3. Fit the pilot bit and shell cutter matched to the pipe material, then open the valve.
  4. Advance at 0.1 – 0.15 mm/r; the pilot bit centres the hole and the cutter follows through.
  5. Retract the bar, close the valve and remove the machine; the branch is ready to pipe up.

Standard scope of supply

  • Hot tapping machine JC-E800-1600, assembled and run-tested
  • Boring bar, 1600 mm travel
  • Tapping adaptor to BS or ASME flange
  • Motor 11 kW, 380 V, 50 Hz with control box
  • Tool kit, seals and operating manual

Before you order

  • Pipe outside diameter, wall thickness and material (steel, cast iron, PE or concrete)
  • Working pressure and medium temperature
  • Flange standard and tapping size required — DN800, DN900, DN1000, DN1200, DN1400, DN1600
  • Cutter type: shell cutter for steel, carbide or diamond for cast iron and concrete
Model range

All models, side by side

ModelTapping range (inch)Tapping range (mm)DriveFeedFeed volume (mm/r)Boring bar travel (mm)Spindle speed (rpm)Motor power (kW)Motor voltage (V)Tapping time (min)Working pressure
JC-M503/4" – 2"DN20 – DN50ManualManual0.15 – 0.2240 / 350———10 – 20≤ 16 bar
JC-DM501/2" – 2"DN15 – DN50Cordless drillManual—3401,300——3 – 10≤ 16 bar
JC-E1002-1/2" – 4"DN65 – DN100ElectricManual3370531.1 / 1.5220 / 3808 – 20≤ 16 bar
JC-E2004" – 8"DN100 – DN200ElectricManual3500401.5220 / 3808 – 20≤ 16 bar
JC-E3004" – 12"DN100 – DN300ElectricManual3600 / 700401.5220 / 3808 – 30≤ 16 bar
JC-E40010" – 16"DN250 – DN400ElectricManual3600 / 800301.538015 – 40≤ 16 bar
JC-E50012" – 20"DN300 – DN500ElectricManual3800302.238025 – 50≤ 16 bar
JC-E60020" – 24"DN500 – DN600ElectricManual0.05 – 0.1900 / 110025438030 – 60≤ 16 bar
JC-E800-160032" – 64"DN700 – DN1600ElectricManual0.1 – 0.1516001011380100 – 240≤ 16 bar

Swipe the table sideways to see every column.

Dimensions and weights are nominal. Pressure ratings are working pressure at ambient temperature; confirm the flange standard and pipe material before ordering.

Related products

Other products in this range

Tell us the pipe, pressure and medium

Send the diameter, working pressure and what flows inside. We reply with a specification and price within one working day.

Send an inquiry →
WeChat Scan to add on WeChat JC-Leon
+86 18130056225